| power4motion |
|
|
 |
|
| Laser Park Assistent model 975EML |
 |
|
|
|
 |
 |
The parking assist projects a laser beam to an easy-to-see spot on the car dash when the car is in the perfect parking position.
- Helps you to park in the right spot, every time
- Works automatically
– the red dot from the laser turns on automatically when you pass the Protector System™
- Simple installation |
|
 |
| Failsafe Infrared Safety Sensor model 770E |
|
|
|
|
 |
|
- IP56
- Current draw - 13 ma max
- Operating voltage - 6 V
- For use with CB3 & all LiftMaster garage door openers
- Red light LED indicates IR beam continuity
- Heavy duty steel brackets protect sensor
- Includes: emitter, detector, brackets, wires and hardware |
|
|
|
| Infrared Sensor model 100263 |
|
|
|
|
 |
|
- System Relay
- Compatible with all common electronic controls
- Approved system
- 12-35V - Wiring NO or NC
- Range: approx. 20m |
|
|
|
| Failsafe Infrared Safety Sensor model 771E |
|
|
|
|
 |
|
- IP44
- Power drain 20mA maximum
- Status LED indicates the IR sensor’s continuity
- Compatible with CB11, CB22, CB3 & all LiftMaster garage door openers
- 2-wire system |
|
|
|
| Flashing Light Kit model FLA24-2 |
|
|
|
|
 |
|
- Power: 24V
- Constant signal input
- Flash board included
- Cable included (2m)
- Can be mounted on walls
- Compatible with CB11, CB22, CB24 |
|
|
|
| Flashing Light Kit model FLA230-2 |
|
|
|
|
 |
|
- Power: 230V
- Constant signal input
- Flash board included
- Antenna & cable included (2m)
- Can be mounted on walls
- Compatible with CB1, CB2 |
|
|
|
| Flashing Light model FLA230 |
|
|
|
|
 |
|
- When connected to a LiftMaster Garage Door Opener the light will flash when the door is in motion
- Provides an additional measure of safety to the installation
- Connects to garage door opener logic board
- Lamp voltage: 230V
- Includes: lamp assembly, light bulb and mounting hardware
- Compatible with LM60, LM600A, LM800A ,LM1000A, 3780 and 5580 |
|
|
|
| 2.5m Safety Edge(Small) model 600046 |
|
|
|
|
 |
|
- 2.5m (8 ft.) rubber profile
- 2.5m (8 ft.) rubber profile mounting rail
- Assembly pack (600060) required |
|
|
|
| Profile (Medium) model 600169 |
|
|
|
|
 |
|
- 8,2K Ohm Safety Edge
- 1m (3.2 ft.) rubber profile medium
- Assembly pack 600152 required |
|
|
|
| Profile (Large) model 600176 |
|
|
|
|
 |
|
- 8,2K Ohm Safety Edge
- 1m (3.2 ft.) rubber profile large
- Assembly pack 600152 required |
|
|
|
| Assembly Pack model 600060 |
|
|
|
|
 |
|
- Assembly pack required for each safety edge
- Closure cap
- Plug with cable
- Connection plug 8.2KOhm
- Cyanacrylat adhesive - 3g
- Abrasive paper
- 600060 for safety edge 600046
- 600152 for safety edge 600169 and 600176 |
|
|
|
| Safety Edge Mounting Rail model G-OSE-C |
|
|
|
|
 |
|
- 2.5m rail
- Aluminium construction
- Fits all safety edges |
|
|
|
| Safety Edge Mounting Rail model 600077 |
|
|
|
|
 |
|
- 20m rail at 2.0m length each
- Zinc coated steel
- Fits all safety edges |
|
|
|
| Interface Box model 600213 |
|
|
|
|
 |
|
- Universal interface box for safety edge
- IP55
- TÜV approved
- Suitable for all gate opener applications
- Safety disabler
- Not required for GOC1A, BAS300K, CB3 |
|
|
|
| Inductive Signal Transfer System model G-INTSET |
|
|
|
|
 |
|
- For sliding doors and gates
- Use instead of coiled cables
- Up to 10m
- Transfers 2-output/2-input signals
- 230V power input
- IP65 |
|
|
|
| Loop Detector 1-Channel model 203292 |
|
|
|
|
 |
|
- 24V AC/DC
- IP40
- Requires no special loop wire
- Training manual available GB/DE
- To be used for safety or as a switch |
|
|
|
| Loop Detector 2-Channel model 203308 |
|
|
|
|
 |
|
- 24V AC/DC
- IP40
- Requires no special loop wire
- Training manual available GB/DE
- To be used for safety or as a switch
- For direction detection or 2 single loops |
|
|
|
|
| Barriers |
 |
|
|
